Finally arrived in Toronto!

Finally arrived in Toronto! This will be our new home 🇨🇦🍁🇨🇦🍁🇨🇦 #canada #sailing #steelboat #toronto #citylife #yacht #liveaboard #travel #explore #ontario #marina #marinalife #boatlife

View on Instagram https://ift.tt/2Ld55FD

Baltimore, Ireland to Baltimore, Maryland

We come from a small village in the southwest coast of Ireland called Baltimore, population 400. Today we dropped our anchor at Baltimore, Maryland, population 611k. We can’t wait to explore this city. Now off to Bushe’s for a pint. #Baltimore #Ireland #Maryland #US #thewire #fiveO #waydowninthehole #sailing #yacht #liveaboard #travel #explore #anchorage #skyline

View on Instagram https://ift.tt/2IgDT2F

Ireland to France- Our first crossing.

After almost a month of pottering around Baltimore, provisioning and making the boat ready for cruising we finally picked a gap in the weather and hit the high seas.

On June 12th we topped up our water and fuel tanks, tied our dingy to the deck and set course for France.

We sailed out the mouth of the harbour passed the beacon at about 2215h. Initially we tried to do 2 hour shifts on watch throughout the night, with one person in the wheel house and one person sleeping in the saloon where they could get up quickly if they were needed.

The first night we kept having trouble with our Aries, self steering (we later modified where the Aries was attached to the tiller to give it a bigger swing and better control the boat even when it went off course) As a result we had a very sporadic sleep pattern for the few nights during crossing from Ireland to France.

We had good wind leaving Ireland that lasted through the first night, first day and into the second day. However on the second day it ended up been flat calm. We dropped our sails and motored through to the 3rd night. As our final day came around we picked up a bit more wind and were able to start sailing again but we still had to keep the motor going to keep us moving at a reasonable 4 knots.

It then took us the most of your 3rd day to get from the shipping lanes off Ouessant to our anchorage in Camaret. Apart from running into a calm patch half way over we were pleased with our first crossing together, no choppy seas and nobody’s lunch was emptied over the side.

Looking forward to a few days of rest we hit our bunks for a full nights sleep.

Cape Clear- A rough night at sea

We wanted to spend a night at sea before we did our first crossing to France. One evening we decided to just sail out towards the Mizen Head. This was not our best idea as this particular night ended up being very rough with very steep choppy waves. We were out about 3 hours out when we decided that it wasn’t worth putting ourselves through a full night of horror. We changed our course and decided to make something out of the sail by sailing into the nearest harbour, Cape Clear North.

It’s a small harbour with steep rock cliffs on either side of the entrance. It was about 2am by the time we made our way into the harbour and tied up at the pier. We eat some lovely vegetarian chilli that Ciara had prepared before we headed off. We then collapsed into bed and fell straight asleep.

The following morning (maybe midday) we were greeted with sunshine and a much calmer day. We spent a few hours tidying up the boat as stuff had falled all over the place the night before. One of our friends paid us a visit in his rib and then we sailed back to Baltimore with a nice following wind.
The experience of the night before was a bit putting off at the time but looking back on it now I think it was good that we got stuck in some really crappy weather, if only for a few hours. it was a bit of a warning to make sure you are properly prepared and that you make sure that you have a good handle on the weather forecast.

Heir Island- A short cruise and a broken camera.

Since we have both finished up work and moved onto the boat we haven’t had very good weather. It has been very windy and quite wet. As a result we haven’t made it far from Baltimore on our shakedown cruises.

We spent a night anchored off heir island where we walked to the far end of the island to take some photos and see the sights. Unfortunately our good camera broke half way through the day so we only got and few nice shots to show you.

I was sad to see the old camera go as I had the camera almost 5 years and it went everywhere with me. We were going to be using the camera a lot we ordered and new body for it straight away. I had no hesitation in getting the same camera as the old one had survived so well and always produced great results. We got the new camera in the post in a few days.

 

 

New ships wheel

Our old wheel took up a lot of room and it was not the prettiest. I decided to make a new wheel out of plywood.
First I cut out 3 rough circles from 5mm plywood. Then I bolted each one to a jig I made for my router.

As I used the same bolt hole to mount each piece of ply there were all identical so they fit together perfectly. I then glued the 3 pieces together and clamped them in the vice overnight.


I marked out where I wanted to cut out material to make the spokes of the wheel.


I used a new hole in my “router table” to cut the 6 radius around the sides of the wheel. I used a drill to make the 6 holes close to the centre of the wheel. Then I used a jig-saw to join the radius to the hole leaving me with 6 triangles removed and 6 spokes for the wheel.


I then used a corner radius bit in the router to round all the edges inside and outside. A hole was drilled in the middle of the wheel to attach the centre piece from the old wheel. I also put a step in the middle that the compass cover would fit into.

It was then just a matter of sanding and varnishing.

Here are some photos of the wheel in the boat and how the mechanism works. since our boat has a tiller the wheel is not always connected, we use this chain to connect and disconnect the pulley system from the wheel.